M O O R E ' S   I D E A L   P R O D U C T S  L L C             Since 1978              Race Proven World and National Champions!
  
mip-part-13165d

MIP Pucks™, 17.5 Drive System, Kyosho RB5/RB6 #13165, *Discontinued*

Be the first one to write a review
13165
Discontinued

More Details

button-enlarge.jpg  Rollover any small image above to change, click small image for hi-res view.

PRODUCT DETAILS

button-instructions.jpg 

UPC# 691545131658

 

 

PRODUCT DESCRIPTION:

“MIP Pucks™” ‘ARE’ the future of 17.5 stock racing! MIP’s all new Puck™ Drive system is an aluminum based drivetrain system which includes aluminum diff outdrives, aluminum C-CVD™ bones, and replaceable plastic orange wear Pucks™ that take the place of inferior steel pins. This combination greatly increases the longevity of the drivetrain and most importantly decreases the drivetrain’s overall rotating mass by a whopping 50%! The decrease in weight directly results in quicker acceleration, deceleration, and lower motor temps! Get the advantage that every stock racer craves! GET, MIP’s all new Hard Anodized 7075-T6 Aluminum Puck™ drive system!

 

TARGET CUSTOMERS:

17.5 Stock Racers

 

COMPETITIVE ADVANTAGES:

Less rotating mass

Quicker acceleration

Quicker deceleration

Lower motor temps

Less overall wear on drive components

 

FEATURES:

Complete MIP Differential

Complete C-CVD™ Axle Set

50% less rotating mass over stock steel components

Replaceable Pucks to keep your drivetrain fresh

Two sets of holes in the C-CVD™ bell

Hard Anodized 7075-T6 Aluminum

Race proven C-CVD™ Construct

MIP Laser Etched Logo

100% Quality made in the USA!

 

INCLUDES:

 

HW-SHSS 4-40 x 3/32 Cup Point (2), Ball Bearing 3/32” Chrome Steel Ball (12), HW-Pin 1/16 x .430 Solid Pin (2), HW-WASHER/ Diff Ring (2), HW-Nut M4 x .7mm Steel Locknut (2), HW- Bearing 1/16” Chrome Steel Ball (7), MIP Thrust Washer(2), HW-BHCS 1-72 x 1/8” (6), MIP 3/16” CVD™ Coupling (2), MIP Capture Rings (2), HW-SHSS, 4-40 x 1/8 Flat point(2), HW-BEARING/ 5/32in x 5/16in x 1/8in Ball Bearing (2), MIP CVD™ Puck Pin (2), MIP Outdrive Pucks™ (8), MIP 12MM Keyed Aluminum Hex Adapters Kyosho (2), MIP Thrust Retainer .236 Aluminum Bore (1), Diff Gear 52T 48P(1), Diff Lube & Grease cup (1), MIP Lube & Thread Gel Cup (1), Inst. Sheet (1), Confetti Sticker (2), MIP CVD™Keyed Rear Axle Kyosho Ultima RB5/RB6 (2), MIP Pucks™ MIP C-

CVD™ Aluminum Bone Kyosho Ultima RB5/RB6 (1), MIP Pucks™ Male Aluminum Outdrive Kyosho SC-R (1), MIP Pucks™ Female Aluminum Outdrive Kyosho SC-R (1)

 

 

REQUIRES:

.050 Allen Key – Equivalent to #9000 MIP Hex Driver Wrench .050 inch

5/64 Allen Key – Equivalent to #9002 MIP Hex Driver Wrench 5/64 inch

Kyosho Tensionner Spring- UM124

Kyosho Ball Diff. Screw Set - LA208

Kyosho Diff. Gear Set - UM509 

 

COMPATIBILITY:

Kyosho Ultima RB5/RB6

 

 

 

SUPPORT PRODUCTS:

(See links below for support kit items.)

 

Safety Data at http://miponline.com/store/msds.html 

Hi Res Images at http://www.miponline.com/store/media/myparts/  or click any image herein.  

 

*Not Responsible for typographical errors

button-reviews.jpg

Click HERE for Race Results, More Reviews, Gallery, and More!

"a MUST have item for any stock class racer."  Facebook, Brett R.

The ULTIMATE stock racing hop up."  Facebook, Brian R.

 

 
   
MIP PUCK System10/04/2013
By Ian Cameron
As soon as you get the bag for the MIP PUCKS system you can tell you're in for a great change to your stock losi SCTE drive line. This center drive system is considerably lighter than the standard setup. My first outing with these was at a tight, high traction indoor track in Columbus Ohio. This is where I feel that the lightened drive line can really make the difference. My truck seemed to accelerate quicker, and seemed to be more agile with the lightened system. I can't wait to see what other lightened products MIP will release for the SCTE.

 

  5 Star ***** Associated 17.5 Pucks system advantage!11/06/2013

By Paul Peterson
I can tell you the Pucks System Helped get me a trophy. At the Last race of the season I put my Pucks system in my SC Dirt Modified and it was enough of an advantage to push me past the other competitors into the 3rd place for the season Trophy. The lighter rotating weight is what helps a lot in all "Blinky" classes... rotating weight is a big factor on speed when you can't time things. Every little bit helps in these very competitive classes. I can thank MIP for the help in me getting a little more trophy hardware this season!!!! 

 
 
MIP Puck Drive System10/25/2013
By David Krider
Very impressed with the new Pucks drive system ----Eustace -you did it again ! I purchased my first MIP product in 1984 --- Trailing arms for the Tamiya Rough Rider. Thank you Dave K aka Chef Dave

 

 
 

kyosho sc and stadium alum axle diff kit.10/13/2013
By Charles Fowler
The new orange puck system is great and have won several races already. Great acceartion for stock 17.5 truck and sc, I did a little work and installed the first MIP RT5 Kyosho stadium truck kit together and it worked great. The way the pucks glide in the outdrives has shown no wear at all. Suggestion recommend everyone to install new ball cups on rear turnbuckles because the pucks will be a little tough to put back during a race......

5 Star ***** Puck drive system09/24/2013 

By Woody Woodruff
Great product, installed the puck drive system this past weekend before the final round of the RC Pro mountain and was very pleased with the added performance they delivered. Just an example of another quality product from MIP!

 

Reviews

  
Write a review | No reviews for this product.

Support Parts:

mip-part-9149d
HW-BEARING/ 3/32in Chrome Steel Ball (12) #09149 *Discontinued*
HW-BEARING/ 3/32in Chrome Steel Ball (12) #09149 *Discontinued*
Average rating:
Add to Cart
mip-part-10112d
HW-BEARING/ 5/32in x 5/16in x 1/8in Ball Bearing (2) #10112 *Discontinued*
Be the first one to write a review
Add to Cart
mip-part-10144
MIP CVD™/C-CVD™ 3/16 Rebuild Kit w/ Set Screws #10144
$6.00
MIP CVD™/C-CVD™ 3/16 Rebuild Kit w/ Set Screws #10144
Average rating:
Add to Cart
mip-part-11115
MIP Capture Rings (4) for all 1/10 MIP CVD™ #11115
$6.00
MIP Capture Rings (4) for all 1/10 MIP CVD™ #11115
Average rating:
Add to Cart
mip-part-13131
MIP Pucks™, Orange No.1 Pucks™ (8) #13131
$6.00
MIP Pucks™, Orange No.1 Pucks™ (8) #13131
Average rating:
Add to Cart
mip-part-13132
MIP Pucks™, No.1 Pins & Screws (2) #13132
$8.00
MIP Pucks™, No.1 Pins & Screws (2) #13132
Average rating:
Add to Cart
mip-part-13163d
MIP Pucks™, Female Aluminum Outdrive, Kyosho SC-R (1) #13163, *Discontinued*
MIP Pucks™, Female Aluminum Outdrive, Kyosho SC-R (1) #13163, *Discontinued*
Average rating:
Add to Cart
mip-part-13166d
MIP Pucks™, MIP C-CVD™ Aluminum Bone, Kyosho RB5/RB6 (1) #13166, *Discontinued*
Be the first one to write a review
Add to Cart
mip-part-99002
HW-BEARING/ Ř1/16 Gr. 25 Ch. Steel Ball (8) #99002
$3.00
Be the first one to write a review
Add to Cart
mip-part-99010
HW-NUT/ M4 x .7mm Steel Nyloc (6) #99010
$3.50
HW-NUT/ M4 x .7mm Steel Nyloc (6) #99010
Average rating:
Add to Cart
mip-part-99016
HW-PIN/ Ř1/16in x .430 Steel (4) #99016
$3.00
Be the first one to write a review
Add to Cart
mip-part-99028
HW-SHSS/ 4-40 x 3/32 Cup Point (4) #99028
$2.50
Be the first one to write a review
Add to Cart
mip-part-99029
HW-SHSS/ 4-40 x 1/8 Flat Point (10) #99029
$3.50
Be the first one to write a review
Add to Cart
mip-part-99064
HW-BHCS/ 1-72 x 1/8 (6) #99064
$3.00
HW-BHCS/ 1-72 x 1/8 (6) #99064
Average rating:
Add to Cart

Your MIP Race Bag

Add These Related Products!

mip-part-09504
MIP Nut Driver Wrench Mega Bundle Set, Metric (5) 4.0mm, 5.0mm, 5.5mm, 7.0mm, & 8.0mm #9504 MSRP:$110.00 MAP: $82.50
$82.50
Add to Cart
mip-part-09505
MIP Nut Driver Wrench Set, SAE Standard (3), 3/16", 1/4", & 11/32" #9505 MSRP:$67.00
$50.25
Add to Cart
mip-part-09503
MIP Nut Driver Wrench Set, Metric (2), 5.5mm & 7.0mm #9503 MSRP:$44.00 MAP: $33.00
$33.00
Add to Cart
mip-part-09501
MIP Hex Driver Wrench Set, SAE Standard (4) , .050", 1/16", 5/64", & 3/32", #9501
$56.00
Add to Cart
mip-part-09502
MIP Hex Driver Wrench Set, Metric (3), 1.5mm, 2.0mm, & 2.5mm #9502
$42.00
Add to Cart
mip-part-09511
MIP Speed Tip™ Hex Driver Wrench Set, SAE Standard (3), 1/16", 5/64", & 3/32" #9511
$39.00
Add to Cart
mip-part-09512
MIP Speed Tip™ Hex Driver Wrench Set, Metric (3) 1.5mm, 2.0mm, & 2.5mm #9512
$39.00
Add to Cart
mip-part-8117
MIP MXT-1 Servo Tape (2 pcs 1in x 5in) #08117
$4.00
Add to Cart